Search Results for ‘baler’

I'm looking for the hose and or fittings to charge the bale density on a NH640 baler. Appreciate any help.

I have a 24t baler works great. Just got done baling a field. Went to clean it out, usually I start the PTO and then manually trip it to make a bale out of the last remaining hay in the chute so I can pull it out. Without thinking I tripped it before I turned the pto on didn't think it was a...

I am currently working on a JD 467 Round Baler that is having issues with the twine arms tying twine around the bale. The baler will form the bale but when the arms are supposed to come out to tie the twine they do not. In addition, the monitor for the baler just shows a stop symbol without...

I was wondering if you all had any good recommendations on belt type round balers. My father and grandfather used a nh 851 chain baler for years and that’s what I started off with and it’s done me good but I need a tighter better looking bale if I am going to sell it. I bought a nh br780 this...

i have a 8585 case baler. trying to bale first time with it this year. hooked my 8R on it which ive never bales with that tracter before but i keep shearing pins in the fly wheel. hay is dry and not that heavy. gear box oil is a little low and going to add that through the breather. trying...

Hey, I have a New Holland BR7090 Specialty Crop Baler and had the Triple Sprocket bearing go out today. Unfortunately wrecked the short shaft that goes towards the gearbox as well. While putting it back together I pushed the bearing as far as it would go onto the shaft then slid the shaft in. By...

Goodevening everyone, This winter I'm planning on working with a machine shop to manufacture and install a reverser on our MF 2250 for backing out plugs. I've had to pull plugged hay out of the feeder a few too many times to enjoy it anymore :). What I'm wondering is, would anyone be interested...

I have a new to me new Holland 853 baler. Works great only issue is the arms wont snap shut to cut the twine. I can bump it manually and it will close. I've cleaned them out and lubed them up and still nothing. any help would be appreciated.

Hello again. I know this maybe a lost cause and some of you may think I am delirious for wanting to do this. however, I am looking for a mesh wrap kit for either a Hesston 560 or a Hesston 565A. I could make one off of a 565 A work but one off of a 560 would be better. I know Agco used to make a...

I have a John Deere 4066R tractor that has engine HP 65.9 and PTO HP 52. I am looking to purchase a round baler. The hayfields have a gradual slope (not steep). Elevation of ground is close to sea level so there should not be a reduction in HP. I have looked at 4x4 and 4x5 round balers. The...

I was wondering if anyone had any experience working on a 605K Vermeer. We have put new belts on the baler and cannot get the belts to tighten up. We have put air in the air bags, adjusted the tense on the baler but no luck. The belts are cut to length from the factory so it shouldn’t be a...

Good day, Recently inherited the Case RBX 561 baler without an owners manual and I am trying to slack the belt tension off in order to swap some belts out. Does anyone have a solution? Tried the following already: 1) Raising the tailgate all the way up and locking it out and then reducing...

Bought a used case ih 8435 silage special round baler, was wondering if anyone has one that could help us find parts? Seems no one has any? Also does this baler have a Heston or new holland baler that parts can interchange with?

My baler will not make a good dense bale. Last year it worked fine. The green gauge on the front is not moving at all. It looks like there is some oil showing in it so Is it supposed to show oil in it? Does anyone know what the pressure (PSI) should be? The gauge only has a +/- no pressure...

Hi Everybody, I'm new to the forum but have been getting advice here as an onlooker for quite some time. We bought a New Holland 273 baler with a 54A kicker attached last year, but didn't have hay wagons. We took the kicker off and baled all last year with it (great older baler, much better...

Hello. I'm new to baling and i bought my own baler (NH 366 - for Europe). Today was the first day of baling. For first time baler gone good. But i have one other problems with twine is everywhere around on the field, on the bale,... It is always about 30 mm long. The problems is viewed on the...

Hi - I'm a new (but very old....79 years old) guy on this forum. Unfortunately I am not a farmer. I am a wood worker and my current project is making a small woodworking model of a "standard" baler knotter operation. My plan is to have a small wood working "automata" that is activated by a hand...

I have a JD 466 round baler. It is not tying very tight on the right side. I have adjusted my monitor to have it wrap 10 times around the roll but it still is loose. I have loosened and tightened and loosened the piece where the string comes out of the baler to the arms. any help????

We are trying to get our hay in and of course the Baler is not cooperating. It is making shaggy bales and baler is throwing hay out the top. We have never seen it do this. Any ideas? I have attached a pic of a bale

Posted not to long ago about baler not working. Found out it was a module terminatir that I needed. Baler is working now but will not auto tie. Anybody know how to troubleshoot that. I can manually tie it but will not auto tie. Also, net wrap is wrapping around feed roller in the net wrap box at...